Ridgid MS1290LZA Uživatelský manuál

OPERATOR’S MANUAL12 in. SLIDING COMPOUND MITER SAW WITH LASERDouble InsulatedMS1290LZAYour miter saw has been engineered and manufactured to our high

10®FEATURESPRODUCT SPECIFICATIONSBlade Diameter ... 12 in.Arbor Hole ...

11FEATURESFig. 2CARRYING HANDLESAW ARM LOCKED IN DOWN POSITIONLOCK PINKNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires a

12FEATURESFig. 5REPEAT-A-CUT®PADLOCKFig. 4SWITCH TRIGGERMITER LOCK LEVERThe miter lock lever securely locks the saw at the desired miter angle.MITER S

13The following tools (not included) are needed for making adjustments or installing the blade:COMBINATION SQUARETOOLS NEEDEDFig. 6COMBINATION WRENCH,

14The following items are included with your miter saw: Dust Bag Dust Bag Frame Dust Guide Work Clamp Blade Wrench Hex Key, 1/16 in. Las

15ASSEMBLYUNPACKINGThis product requires assembly. Carefully lift saw from the carton by the carrying handle and the saw base, and place it on a lev

16ASSEMBLYFig. 9NOTE: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we

17ASSEMBLYFig. 11INSTALLING THE DUST BAGSee Figure 11. Squeeze the metal clips on the dust bag, then slide the metal ring over the end of the dust g

1818 WARNING:Make sure the spindle lock button is not engaged before reconnecting saw to power source. Never engage spindle lock button when blade is

1919ASSEMBLY DANGER: Laser radiation. Avoid direct eye contact with light source.ALIGNING THE LASER GUIDE LINESee Figure 14.The laser guide will gene

2TABLE OF CONTENTS Introduction ...

20ASSEMBLYREMOVING / REPLACING THE ZERO CLEAR-ANCE THROAT PLATESee Figure 15.When squaring the saw blade, it may be necessary to move the thr

21Fig. 19FENCESOCKET HEAD SCREW(S)FENCE SCREWSOCKET HEAD SCREWASSEMBLYADJUSTING THE MITER LOCK LEVERSee Figures 17 - 18.Prior to squaring the saw blad

22INDICATOR SCREWSCALE INDICATORMITER SCALE®®®ASSEMBLYVIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIREDFig. 23SLIDING MITER FENCEFRAMING

23ASSEMBLYADJUSTING THE BEVEL LOCK LEVERSee Figures 24 - 25.Prior to squaring the saw blade to the miter table, check and align the bevel lock lever

24SOCKET HEAD SCREWSCALE INDICATOR®INDICATOR SCREWSQUARING THE BLADE TO THE MITER TABLESee Figures 27 - 30. Unplug the saw. Pull the saw arm all t

25OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to

26OPERATION WARNING:Never make a cut by pulling the saw toward you as the blade can climb on top of the workpiece and come toward you. Failure

27Fig. 33OPERATIONWORK CLAMP®CROSS CUTTO MAKE NON-SLIDING CUTS WARNING:Securely tighten the slide lock knob when making any non-sliding cuts. Failu

28®TO BEVEL CUTSee Figures 35 - 37.A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece.

2922.531.6TO COMPOUND MITER CUTSee Figure 38.A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of c

3 WARNING:Read and understand all instructions. Failure to follow all instructions listed below, could result in electric shock, fire and/or serious

30®SUPPORTING LONG WORKPIECESSee Figures 39 - 40.Long workpieces need extra supports. Supports should be placed along the workpiece so it does not sag

31OPERATIONROUGH CUTTING A DADOSee Figures 42 - 43.Using a wood chisel and the depth guide, it is possible to make a rough dado cut. The marks on the

32CUTTING COMPOUND MITERSTo aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are the

33When cutting crown molding by this method, the bevel angle should be set at 33.85°. The miter angle should be set at 31.6° either right or left, dep

34OPERATIONMAKING A CROWN MOLDING SUPPORT JIGSee Figure 46.A crown molding support jig will need to be made when cutting crown molding with n

35CUTTING WARPED MATERIALSee Figures 47 - 48.When cutting warped material, always make sure it ispositioned on the miter table with the convex

36® WARNING:When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. WARNING:Al

37MAINTENANCE WARNING:Failure to unplug the saw could result in accidental starting causing serious injury. Remove brush cap with a screwdriver. Br

38NOTESACCESSORIESLook for these accessories at The Home Depot. AC9940 ... Miter Saw Utility Vehicle WARNING:Curre

39WARRANTYProof of purchase must be presented when requesting war-ranty service.Limited to RIDGID® hand held and stationary power tools purchased 2/1/

4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICALLY. If

40CUSTOMER SERVICE INFORMATIONFor parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information

5SPECIFIC SAFETY RULES NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. NEVER reach behind, unde

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of

7SYMBOLS SYMBOL SIGNAL MEANINGSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service

8ELECTRICALDOUBLE INSULATIONDouble insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push