Ridgid TP1300LS Uživatelský manuál Strana 1

Your new planer has been engineered and manufactured to our high standards for dependability, ease of operation, andoperator safety. When properly car

10PULL OUT TO LOCKKNIFE TOOLFig. 4WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

11ASSEMBLYASSEMBLING LEG STANDSee Figures 5 and 6. Separate brace pieces from leg pieces. There are a totalof 16 pieces: 8 brace pieces and 8 leg pie

121RepeatCutA--111113322""4444811131/83/321/161/3202.521.51.50IndICut654210 012345678910111213141531RepeatCutA--111113322""4444811

13ASSEMBLYFig. 9Fig. 10MOUNTING PLANER TO WORKBENCHIf your planer is to be used in a permanent location, it isrecommended you secure it to a workbench

1RepeatCutA--111113322""44448111654210 01234567891011121314153654210 012345678910111213141531RepeatCutA--111113322""4444811131/83/

654210 01234567891011121314153THICKNESS SCALE ADJUSTMENTSee Figure 12.Located on the right front of the planer, the thickness scaleshows the depth of

RESETOFFOPULLONIPUSHRESETOFFOPULLONIPUSHPULL OUT TO LOCKRESETOFFOPULLONIPUSHPULL OUT TO LOCKPULL OUT TO LOCKOPERATIONONGETTING STARTEDBefore turning o

1RepeatCutA--111113322""4444811131/83/321/161/3202.521.51.50IndICut654210 012345678910111213141531RepeatCutA--111113322""444481113

MAINTENANCEWARNING:When servicing, use only identical replacementparts. Use of any other part may create a hazard orcause product damage.GENERALAvoid

MAINTENANCE If you are changing to the second side of the blade,rotate the blade “end for end” keeping the same flat sidedown. This correctly positio

2TABLE OF CONTENTS Introduction ...

MAINTENANCEGENERAL MAINTENANCEWARNING:Always begin by disconnecting the power supply. Periodically check all clamps, nuts, bolts, and screws fortigh

TROUBLESHOOTING1. Replace, turn or sharpen cutter blades2. Butt pieces end-to-end as they are fedinto planer3. Securely tighten mounting hardware4. Lo

WARRANTY22This product is manufactured by One World Technologies,Inc., under a trademark license from Ridgid, Inc. All warrantycommunications should

NOTES23

24CUSTOMER SERVICE INFORMATIONFor parts or service, contact your nearest Ridgid authorized service center. Be sure to provide all relevant information

3The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations with them, deserve your caref

4RULES FOR SAFE OPERATION KEEP THE WORK AREA CLEAN. Cluttered work areasand work benches invite accidents. DO NOT leave toolsor pieces of wood on the

5RULES FOR SAFE OPERATION NEVER PERFORM THE PLANING OPERATION withthe cutter head or cutter guard removed. NEVER MAKE A PLANING CUT deeper than 1/

6ELECTRICALEXTENSION CORDSUse only 3-wire extension cords that have 3-prong groundingplugs and 3-pole receptacles that accept the tool's plug.Whe

7SPECIFICATIONSFeed Rate ...

81RepeatCutA--111113322""44448111KNIFE TOOL31/83/321/161/3202.521.51.50IndICut654210 01234567891011121314153FEATURESFig. 2KNOW YOUR PORTABLE

9TOOLS NEEDEDThe following tools (not included) are needed for checking adjustments of your planer:13 mm COMBINATION WRENCH (2)FRAMING SQUARE Do not