RIDGID metal detector Uživatelská příručka Strana 113
- Strana / 144
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Operating Instructions
If it cannot then a warning message will be displayed and a larger metal contaminant
may need to be used. Once a successful inspection of the Fe test wand has been
completed, the user is prompted to pass the same sample product pack with the test
wand attached through the detector a number of times, set in the Number of passes
option, until they have all passed inspection and the test is complete in the PVS screen
as shown below.
The user is then prompted to repeat the above process for the Nfe and then the S.St test
wands.
Once all testing has been completed successfully, normal inspection can be continued.
The test wands are colour coded RED – Fe (Ferrite), GREEN – NFe (Non-Ferrite) and
BLUE – S.St (Stainless Steel).
O Sequential
Selecting this option enables the sequential process which is basically the same as the
Normal process with the exception that each of the test wand types is passed one after
the other through the detector rather than one type at a time until they have all passed
inspection and the test is complete.
■ Timing
The following options are available for setting the test timing to be used.
O Off
Selecting this option means that the user will initiate a PV test manually from the Menus
> Run PV Test menu.
O Interval
Selecting this option means that the user will be automatically prompted to initiate a PV
test after a specified time, subject to a minimum interval of 6 minutes.
O Batch
Selecting this option means that the user will be automatically prompted to initiate a PV
test when a new batch is started or when a batch ends.
A Product Registration Photo-eye must be fitted to use the Interval and Batch options.
■ Test Window
This option is only displayed when either the Interval or Batch Test timing option is selected. It
is used to set a length of time in minutes to successfully complete a PV test, commencing
from the generation of the prompt. When using the Interval Test timing option, the length of
time set cannot be shorter then the time set in the Interval field.
■ Number of passes
This field is displayed for all test types and timing options. It is used to set the number of
passes required for each test wand type to complete a PV test.
103
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Související produkty a manuály pro Měření, testování a kontrola RIDGID metal detector
(5 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce