RIDGID metal detector Uživatelská příručka Strana 30
- Strana / 144
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Safety First
10. CONTAMINANTS. Oils and greases must always be handled with care. Prolonged bare skin
exposure to certain oils and greases can cause skin problems. Always handle oils and greases in
accordance with the manufacturer‘s instructions.
11.
TRAPPED FINGERS. Do not place fingers on the underside of the conveyor when the metal
detector is operating. It is possible for fingers to be trapped and subsequently crushed between a
moving and fixed component.
12.
WARNING LABELS. Loma metal detectors have a number of safety labels attached to highlight
potentially hazardous areas. Particular attention should be paid to the location of these labels
and their significance in operating the metal detector safely. If necessary, labelling is provided in
the local language to meet legislative requirements.
13. GUARDS. No metal detector is to be run without guards fitted unless for maintenance purposes
and only if adequate precautions have been taken. Under no circumstances is any interlock to be
defeated.
14.
OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION WARNING. In the USA, the
Occupational Safety and Health Administration (OSHA) Acts quite clearly place the burden of
compliance on the user of equipment, and the acts are generalised to the extent that
determination of adequacy of compliance is a judgement decision on the part of the local
inspector. Hence Loma cannot be held responsible for meeting full requirements of OSHA or
OHSA. with regards to any equipment supplied, nor can Loma be held liable for penalty which
may be assessed for failure to meet the requirements of the acts as interpreted by an authorised
inspector.
15.
LIABILITY. This machinery contains high voltages of a hazardous and potentially fatal nature.
Loma Systems cannot accept any liability for death or bodily injury resulting from
improper work
undertaken by unqualified operatives, or due to deviations from
the maintenance instructions
within this manual. This Liability statement is in addition to the terms of sale.
16.
HEIGHT ADJUSTMENT. Care should be taken when adjusting the height of
Pipeline
detectors.
Lower the height adjustment to its minimum before moving. If
appropriate
measures
are not
taken, severe injury to an individual or damage to the
detector
could result.
17.
SECURITY WHEN STAND MOUNTED. Due to the high centre of gravity, care should be taken
when moving a pipeline metal detector on a stand as the applied force and/or obstructions of the
wheels may cause the machine to fall over. This could result in death or severe injury to an
individual and/or severe damage to the detector.
18.
START UP WITH AUTOMATIC REJECT
VALVE.
When a pipeline is switched on, the automatic
reject valve changes state from “Reject” mode to “Run” mode. Do not
put
any part of the body
within close proximity of the reject valve outlet when the machine is switched on. This could
result in severe injury to an
individual.
19.
HEIGHT ADJUSTMENT STAND-MOUNTED VERSIONS. When adjusting the height of a
detector assembly, do not unscrew the locating screw in the height
adjustment strut. If it is
unscrewed and removed, the body of the detector and the reject valve may spin round on the
height adjustment strut, causing the machine to fall over. This could result in death or severe
injury to an individual and/or severe damage to the detector.
20.
SECURITY. The detector is mounted on a gas-filled height-adjustment strut. After adjusting the
height of the detector, make sure the adjustment handle is
fully tightened. If the handle is not fully
tightened,the detector could rise on the
strut.
This could result in severe injury to an individual
and/or severe damage to
the
detector.
21.
H
ANDLING A HINGE MOUNTED VERSION ON A HANDTMANN PA30 FILLER. When a
pipeline is mounted on a PA30, the detector must be removed from the PA30 before
disconnecting the PA30 from the main filler. Failure to do this may result in
the PA30 falling over
resulting in death or severe injury to an individual and/or severe damage to the PA30.
22.
HANDLING A HINGE MOUNTED VERSION WITHOUT A STAND. Care should be taken when
fitting or removing the detector off the filler hinge. The detector should
be lifted by two persons. If
lifting is attempted by a single person this could result in
death or severe injury to an individual
and/or severe damage to the
detector.
20
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Související produkty a manuály pro Měření, testování a kontrola RIDGID metal detector
(5 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce